Sign In
Ask Question
Engineering
Emiliano Glenn
25 July, 19:03
24) When first turning a jigsaw on, one should:
+1
Answers (
1
)
Alexis Duffy
25 July, 19:55
0
Simple Answer:
Always make sure you are using the right blade for the material. Make sure you put on safety goggles and use THICC gloves. DO NOT start cutting when children are around, as it is possible they may get hurt.
Answer:
"1
Plug in the saw or put in the battery pack. Once you have your saw blade secured, plug the cord into a nearby outlet so you can reach all the areas you need to cut. If you have a cordless jigsaw, insert the battery pack into the port on the back of the machine.[7]
Whenever you aren't using your jigsaw, unplug it so you don't accidentally turn it
Coil the cord once around your dominant arm so the cord doesn't hang down loosely.
2
Wear safety glasses and a dust mask. Before you make any cuts, cover your mouth and nose with a face mask so you don't inhale any dust. Protect your eyes with safety glasses in case any of your material kicks back towards you.[8]
3
Clamp your material to your work surface so it doesn't move around. Make sure the area where you plan on making your cuts extends over the edge of your work surface. Use at least 2 C-clamps on the edge of your work surface to hold the material sturdy. If it still moves around easily, use additional clamps or rest a heavy object on the opposite end of the material.[9]
If you need to cut a hole in the center of your material, balance it between 2 sawhorses so you can easily cut through it without damaging your work surface.
You don't need to use clamps if you're making a vertical cut on a wall."
-How to Use a Jigsaw Co-authored by WikiHow Staff | Reader-Approved | 19 References Updated: March 29, 2019
Comment
Complaint
Link
Know the Answer?
Answer
Not Sure About the Answer?
Get an answer to your question ✅
“24) When first turning a jigsaw on, one should: ...”
in 📙 Engineering if there is no answer or all answers are wrong, use a search bar and try to find the answer among similar questions.
Search for Other Answers
You Might be Interested in
A resistor, inductor and capacitor are connected in series, each with effective (rms) voltage of 65 V, 140 V and 80 V, respectively. If the resistor is rated at 24 W, what is the average power dissipated in the circuit
Answers (1)
Technician A says that as wheelbase becomes shorter in a highway truck, its resistance to yaw is reduced. Technician B says that an ABS add-on called directional stability control uses the brake system to avoid tracking yaw. Who is correct?
Answers (1)
You just realized the turn signal on your vehicle is broken, and you need to signal that you're turning left. What is the correct way to do it?
Answers (2)
A rigid tank initially contains 1.4 kg saturated liquid water at 200∘C. At this state, 25 percent of the volume is occupied by water and the rest by air. Now heat is supplied to the water until the tank contains saturatd vapor only.
Answers (1)
For the following conditions determine whether a CMFR or a PFR is more efficient in removing a reactive compound from the waste stream under steady-state conditions with a first-order reaction: reactor volume = 280 m3, flow rate =
Answers (1)
New Questions in Engineering
Familiarity with basic fastener properties: For each of the standard fasteners specified informally below, determine the major diameter d, the pitch p, the pitch diameter dp, and the bolt length L.
Answers (1)
The diameter of a cylinder is called the a.) stroke b.) bore c.) principal length d.) radius
Answers (1)
Consider the following grooves, each of width W, that have been machined from a solid block of material. (a) For each case obtain an expression for the view factor of the groove with respect to the surroundings outside the groove.
Answers (1)
What is the last step to the design process? A: Define the problem B: Present solution C: Evaluate a solution D: Develop a solution
Answers (1)
The controller can be considered the brain of closed loop system
Answers (1)
Home
»
Engineering
» 24) When first turning a jigsaw on, one should:
Sign In
Sign Up
Forgot Password?