A cylindrical rod 100 mm long and having a diameter of 10.0 mm is to be deformed using a tensile load of 27,500 N. It must not experience either plastic deformation or a diameter reduction of more than 7.5*10-3 mm. Of the materials listed as follows, which are possible candidates? Justify your choice (s).

Material Modulus of Elasticity (GPa) Yield Strength (MPa) Poission's Ratio

Aluminum alloy 70 200 0.33

Brass alloy 101 300 0.34

Steel alloy 207 400 0.3

Titanium alloy 107 650 0.34

Question

Engineering

Aniyah Frey

21 May, 21:55

A cylindrical rod 100 mm long and having a diameter of 10.0 mm is to be deformed using a tensile load of 27,500 N. It must not experience either plastic deformation or a diameter reduction of more than 7.5*10-3 mm. Of the materials listed as follows, which are possible candidates? Justify your choice (s).

Material Modulus of Elasticity (GPa) Yield Strength (MPa) Poission's Ratio

Aluminum alloy 70 200 0.33

Brass alloy 101 300 0.34

Steel alloy 207 400 0.3

Titanium alloy 107 650 0.34

+3

Answers (1)

Know the Answer?

Mariah · Answer 1

The steel is a candidate.

Explanation:

Given

P = 27,500 N

d₀ = 10.0 mm = 0.01 m

Δd = 7.5*10 ⁻³ mm (maximum value)

This problem asks that we assess the four alloys relative to the two criteria presented. The first criterion is that the material not experience plastic deformation when the tensile load of 27,500 N is applied; this means that the stress corresponding to this load not exceed the yield strength of the material.

Upon computing the stress

σ = P/A₀ ⇒ σ = P / (π*d₀²/4) = 27,500 N / (π * (0.01 m) ²/4) = 350*10⁶ N/m²

⇒ σ = 350 MPa

Of the alloys listed, the Ti and steel alloys have yield strengths greater than 350 MPa.

Relative to the second criterion, (i. e., that Δd be less than 7.5 * 10 ⁻³ mm), it is necessary to calculate the change in diameter Δd for these four alloys.

Then we use the equation υ = - εx / εz = - (Δd/d₀) / (σ/E)

⇒ υ = - (E*Δd) / (σ*d₀)

Now, solving for ∆d from this expression,

∆d = - υ*σ*d₀/E

For the Aluminum alloy

∆d = - (0.33) * (350 MPa) * (10 mm) / (70*10³MPa) = - 0.0165 mm

0.0165 mm > 7.5*10 ⁻³ mm

Hence, the Aluminum alloy is not a candidate.

For the Brass alloy

∆d = - (0.34) * (350 MPa) * (10 mm) / (101*10³MPa) = - 0.0118 mm

0.0118 mm > 7.5*10 ⁻³ mm

Hence, the Brass alloy is not a candidate.

For the Steel alloy

∆d = - (0.3) * (350 MPa) * (10 mm) / (207*10³MPa) = - 0.005 mm

0.005 mm < 7.5*10 ⁻³ mm

Therefore, the steel is a candidate.

For the Titanium alloy

∆d = - (0.34) * (350 MPa) * (10 mm) / (107*10³MPa) = - 0.0111 mm

0.0111 mm > 7.5*10 ⁻³ mm

Hence, the Titanium alloy is not a candidate.